THỐNG KÊ

  • Khách đang online: 41
  • Truy cập hôm nay: 130
  • Lượt truy cập: 504100
  • Số trang xem: 561899
  • Tổng số danh mục: 25
  • Tổng số sản phẩm: 106

QUẢNG CÁO

Bạn đang ở: Trang chủ » Danh mục » BỘ CHUYỂN ĐỔI TÍN HIỆU » Bộ chuyển đổi tín hiệu HART DC 52500

Dùng cuộn chuột thay đổi chế động phóng to ảnh

Click để xem ảnh lớn !

Bộ chuyển đổi tín hiệu HART DC 52500

Mã SP: DC 52500

Giá bán: liên hệ

Tình trạng: Còn hàng

Bảo hành: 12 THÁNG

Số lượng:

Chia sẻ sản phẩm trên mạng xã hội:


BỘ CHUYỂN ĐỔI TÍN HIỆU DRAGO

BỘ CÁCH LY TÍN HIỆU HART DC52500

KHUẾCH ĐẠI, CÁCH LY CHO TÍN HIỆU HART THAY THẾ CHO BỘ CHUYỂN ĐỔI WEIDMULLER, BỘ CHUYỂN ĐỔI M-SYSTEM, BỘ CHUYỂN ĐỔI PHONIX CONTACT, BỘ CHUYỂN ĐỔI TÍN HIỆU INOR, BỘ CHUYỂN ĐỔI TÍN HIỆU MTL, BỘ CHUYỂN ĐỔI TÍN HIỆU TURCK, BỘ CHUYỂN ĐỔI TÍN HIỆU YOKOGAWA, BỘ CHUYỂN ĐỔI TÍN HIỆU SENECA... 

THÔNG SỐ KỸ THUẬT CỦA BỘ CÁCH LY HART DC52500

Technical Data

Input

Input signal 0/4 to 20 mA (4 to 20 mA with HART signal)
Input resistance ≤ 50 Ohm  
Over load 50 mA / 30 V  
Transmitter supply (Tx) 16 V (open circuit voltage/short circuit current < 22 V/35 mA)
Communication signal Bidirectional HART transmission, internal AC impedance ~ 250 Ohm

Output

Output signal 0/4 to 20 mA (4 to 20 mA with HART signal)
Load 0 to 600 Ohm (at 20 mA) (230 Ohm to 600 Ohm with HART signal)
Linear transmission range –1 to +110 %
Ripple < 10 mVrms

General Data

Transmission error < 0.1 % full scale
Temperature coefficient 1) < 100 ppm/K
Cut-off frequency -3 dB 100 Hz, > 2.5 kHz  HART signal
Response time T99 7 ms
Test voltage 3 kV AC, 50 Hz, 1 min, Input against output against power supply
Working voltage 2)
(Basic Insulation)
Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 between all circuits.
Protection against electrical shock 2) Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits.
Ambient temperature  Operation
Transport and storage
–25 °C to +70 °C   (-13 to +158 °F)
–40 °C to +85 °C   (-40 to +185 °F)
Power supply 24 V DC, 16.8 V to 31.2 V DC, ca. 1.3 W
EMC 3) EN 61326-1
Construction 6.2 mm housing, protection class: IP 20, mounting on 35 mm DIN rail acc. to EN 60715
Weight Approx. 70 g
  1. Average TC based on the final value in specified operating temperature range
  2. As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices.
  3. Minor deviations possible during interference

Block diagram

<p>Speisetrenner HART DC 52500<br>Repeater Power Supply HART DC 52500</p>

Dimensions

Masszeichnung-mitBus

Connection
Captive plus-minus clamp screws
Wire cross-section max. 2.5 mm² / AWG 14
Stripped length 6 to 8 mm / 0.28 in
Screw terminal torque 0.8 Nm / 7 lbf in
Optional power connection via In-Rail-Bus (see accessories)

Terminal assignments

1 + Transmitter supply voltage
2 + Input current
3 - Input GND
4   n.c.
     
5 + Output
6 - Output
     
7 + Power supply (connected to In-Rail-Bus)
8 - Power supply (connected to In-Rail-Bus)

Liên hệ để được tư vấn:

Long Tran

Mob.: +84 909 006 435

Email.: long.tran@aumyco.com

AU MY technology Service Trading Company limited

Add.: 93/36 Street 02, Tam Binh Ward, Thu Duc District, Ho Chi Minh city, Vietnam

Tel.: +84 3 816 2902      Fax: +84 3 816 2902

Web.:    www.aumyco.com          Email.: info@aumyco.com          

www.tbcongnghiep.com             

www.chuyendoitinhieu.com     

www.doluongcongnghiep.com

BỘ CHUYỂN ĐỔI TÍN HIỆU DRAGO BỘ CÁCH LY TÍN HIỆU HART DC52500 KHUẾCH ĐẠI, CÁCH LY CHO TÍN HIỆU HART. THÔNG SỐ KỸ THUẬT CỦA BỘ CÁCH LY HART DC52500 Technical Data Input Input signal 0/4 to 20 mA (4 to 20 mA with HART signal) Input resistance ≤ 50 Ohm Over load 50 mA / 30 V Transmitter supply (Tx) 16 V (open circuit voltage/short circuit current < 22 V/35 mA) Communication signal Bidirectional HART transmission, internal AC impedance ~ 250 Ohm Output Output signal 0/4 to 20 mA (4 to 20 mA with HART signal) Load 0 to 600 Ohm (at 20 mA) (230 Ohm to 600 Ohm with HART signal) Linear transmission range –1 to +110 % Ripple < 10 mVrms General Data Transmission error < 0.1 % full scale Temperature coefficient 1) < 100 ppm/K Cut-off frequency -3 dB 100 Hz, > 2.5 kHz HART signal Response time T99 7 ms Test voltage 3 kV AC, 50 Hz, 1 min, Input against output against power supply Working voltage 2) (Basic Insulation) Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 between all circuits. Protection against electrical shock 2) Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits. Ambient temperature Operation Transport and storage –25 °C to +70 °C (-13 to +158 °F) –40 °C to +85 °C (-40 to +185 °F) Power supply 24 V DC, 16.8 V to 31.2 V DC, ca. 1.3 W EMC 3) EN 61326-1 Construction 6.2 mm housing, protection class: IP 20, mounting on 35 mm DIN rail acc. to EN 60715 Weight Approx. 70 g Average TC based on the final value in specified operating temperature range As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices. Minor deviations possible during interference Block diagram

Speisetrenner HART DC 52500
Repeater Power Supply HART DC 52500

Dimensions Masszeichnung-mitBus Connection Captive plus-minus clamp screws Wire cross-section max. 2.5 mm² / AWG 14 Stripped length 6 to 8 mm / 0.28 in Screw terminal torque 0.8 Nm / 7 lbf in Optional power connection via In-Rail-Bus (see accessories) Terminal assignments 1 + Transmitter supply voltage 2 + Input current 3 - Input GND 4 n.c. 5 + Output 6 - Output 7 + Power supply (connected to In-Rail-Bus) 8 - Power supply (connected to In-Rail-Bus) Liên hệ để được tư vấn: Long Tran Mob.: +84 909 006 435 Email.: long.tran@aumyco.com AU MY technology Service Trading Company limited Add.: 93/36 Street 02, Tam Binh Ward, Thu Duc District, Ho Chi Minh city, Vietnam Tel.: +84 3 816 2902 Fax: +84 3 816 2902 Web.: www.aumyco.com Email.: info@aumyco.com www.tbcongnghiep.com www.chuyendoitinhieu.com www.doluongcongnghiep.com
  • BỘ CHUYỂN ĐỔI TÍN HIỆU DRAGO
  • BỘ CÁCH LY TÍN HIỆU HART DC52500
  • KHUẾCH ĐẠI, CÁCH LY CHO TÍN HIỆU HART.
  • THÔNG SỐ KỸ THUẬT CỦA BỘ CÁCH LY HART DC52500
  • Technical Data
  • Input
  • Input signal 0/4 to 20 mA (4 to 20 mA with HART signal)
  • Input resistance ≤ 50 Ohm
  • Over load 50 mA / 30 V
  • Transmitter supply (Tx) 16 V (open circuit voltage/short circuit current < 22 V/35 mA)
  • Communication signal Bidirectional HART transmission, internal AC impedance ~ 250 Ohm
  • Output
  • Output signal 0/4 to 20 mA (4 to 20 mA with HART signal)
  • Load 0 to 600 Ohm (at 20 mA) (230 Ohm to 600 Ohm with HART signal)
  • Linear transmission range –1 to +110 %
  • Ripple < 10 mVrms
  • General Data
  • Transmission error < 0.1 % full scale
  • Temperature coefficient 1) < 100 ppm/K
  • Cut-off frequency -3 dB 100 Hz, > 2.5 kHz HART signal
  • Response time T99 7 ms
  • Test voltage 3 kV AC, 50 Hz, 1 min, Input against output against power supply
  • Working voltage 2)
  • (Basic Insulation) Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 between all circuits.
  • Protection against electrical shock 2) Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits.
  • Ambient temperature Operation
  • Transport and storage –25 °C to +70 °C (-13 to +158 °F)
  • –40 °C to +85 °C (-40 to +185 °F)
  • Power supply 24 V DC, 16.8 V to 31.2 V DC, ca. 1.3 W
  • EMC 3) EN 61326-1
  • Construction 6.2 mm housing, protection class: IP 20, mounting on 35 mm DIN rail acc. to EN 60715
  • Weight Approx. 70 g
  • Average TC based on the final value in specified operating temperature range
  • As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices.
  • Minor deviations possible during interference
  • Block diagram
  • Speisetrenner HART DC 52500
    Repeater Power Supply HART DC 52500

  • Dimensions
  • Masszeichnung-mitBus
  • Connection
  • Captive plus-minus clamp screws
  • Wire cross-section max. 2.5 mm² / AWG 14
  • Stripped length 6 to 8 mm / 0.28 in
  • Screw terminal torque 0.8 Nm / 7 lbf in
  • Optional power connection via In-Rail-Bus (see accessories)
  • Terminal assignments
  • 1 + Transmitter supply voltage
  • 2 + Input current
  • 3 - Input GND
  • 4 n.c.
  • 5 + Output
  • 6 - Output
  • 7 + Power supply (connected to In-Rail-Bus)
  • 8 - Power supply (connected to In-Rail-Bus)
  • Liên hệ để được tư vấn:
  • Long Tran
  • Mob.: +84 909 006 435
  • Email.: long.tran@aumyco.com
  • AU MY technology Service Trading Company limited
  • Add.: 93/36 Street 02, Tam Binh Ward, Thu Duc District, Ho Chi Minh city, Vietnam
  • Tel.: +84 3 816 2902 Fax: +84 3 816 2902
  • Web.: www.aumyco.com Email.: info@aumyco.com
  • www.tbcongnghiep.com
  • www.chuyendoitinhieu.com
  • www.doluongcongnghiep.com

BÌNH LUẬN


0 bình luận về "Bộ chuyển đổi tín hiệu HART DC 52500"

GỬI BÌNH LUẬN HOẶC CÂU HỎI CỦA BẠN

Bình luận hay có ý kiến đóng góp. Vui lòng điền vào form bên dưới và gửi cho chúng tôi.

Email:

Nội dung:

Tôi muốn nhận câu trả lời về câu hỏi này qua email


Bộ cách ly tín hiệu 5104 pr electronics

Giá bán: liên hệ

Tình trạng:
Hiện có: 0 bình luận

cách ly tín hiệu DH1000

Giá bán: liên hệ

Tình trạng:
Hiện có: 0 bình luận

BỘ CÁCH LY TÍN HIỆU DH18

Giá bán: liên hệ

Tình trạng:
Hiện có: 0 bình luận